1102 silver lake road cary il 60013 phone fax 800-981-0363 847-639-1508 e-mail web cp@coilcraft.com www.coilcraft-cps.com ? ? coilcraft, inc. 2009 these parts are preproduction products for electrical evaluation only. specification subject to change without notice. aerospace grade chip inductors ae312rah 0603 chip inductors document ae431-1 revised 06/02/09 a b overall e terminal f d d g c h recommended land pattern terminal wraparound: approx 0.007/0,18 both ends abcde 0.063 0.008 0.031 0.008 0.031 0.008 0.012 0.004 0.031 0.006 1,6 0,2 0,8 0,2 0,8 0,2 0,3 0,1 0,8 0,15 fgh 0.027 0.075 0.035 inches 0,7 1,9 0,9 mm typical q vs frequency 1 10 100 1000 10000 frequency (mhz) 0 100 90 80 70 60 50 40 30 20 10 110 120 q factor 20 nh 3.6 nh 47 nh 100 nh typical l vs frequency 1 10 100 1000 10000 frequency (mhz) 0 100 90 80 70 60 50 40 30 20 10 110 120 inductance (nh) 20 nh 3.6 nh 47 nh 100 nh this robust version of coilcraft?s standard 0603me series features high temperature materials that pass nasa low outgassing specifications and allow operation in ambient temperatures up to 155c. the leach-resistant base metalization with tin-lead (sn-pb) terminations ensures the best possible board adhesion. all dimensions are without solder applied to the terminations. for maximum dimensions with solder, add 0.006 inches / 0,152 mm. high srf, excellent q values and low dcr 45 inductance values from 2.2 nh to 470 nh, some not found in any of our other 0603 series comparable with other industry standards irms derating -40 -55 -20 0 20 40 60 80 100 160 140 120 ambient temperature (c) percent of rated rms i 120 110 100 90 80 70 60 50 40 30 20 10 0 25c core material ceramic terminations tin-lead (63/37) over s ilver-platinum-glass frit ambient temperature ?55c to +125c with i max current, +125c to +155c with derated current storage temperature component: ?55c to +155c. packaging: ?55c to +80c resistance to soldering heat max three 40 second reflows at +260c, parts cooled to room temperature between cycles temperature coefficient of inductance (tcl) +25 to +155 ppm/c moisture sensitivity level (msl) 1 (unlimited floor life at <30c / 85% relative humidity) enhanced crush-resistant p ackaging 2000 per 7 reel. paper tape: 8 mm wide, 1 mm thick, 4 mm pocket spacing suggested land pattern
ae312rah series (0603) 1102 silver lake road cary il 60013 phone fax 800-981-0363 847-639-1508 e-mail web cp@coilcraft.com www.coilcraft-cps.com ? ? coilcraft, inc. 2009 these parts are preproduction products for electrical evaluation only. specification subject to change without notice. 0603 chip inductors document ae431-2 revised 06/02/09 inductance 2 percent q 3 q typ at q typ at q typ at srf min 4 dcr max 5 i max part number 1 (nh) tolerance nom 300 mhz 800 mhz 1.5 ghz (mhz) (ohms) (ma) ae312rah2n2jsz 2.2 5 29 39 60 83 13500 0.024 2500 ae312rah3n6jsz 3.6 5 25 45 75 95 6000 0.059 1600 ae312rah3n9jsz 3.9 5 35 45 75 95 6000 0.059 1600 ae312rah4n3jsz 4.3 5 35 45 75 95 6000 0.059 1600 ae312rah4n7jsz 4.7 5 35 39 64 88 6000 0.047 1600 ae312rah5n6jsz 5.6 5 35 45 75 95 6000 0.082 1400 ae312rah6n2jsz 6.2 5 35 45 75 95 6000 0.082 1400 ae312rah6n8jsz 6.8 5 35 45 80 100 6000 0.082 1400 ae312rah7n5jsz 7.5 5 35 45 80 100 6000 0.090 1300 ae312rah8n2jsz 8.2 5 26 50 84 122 6000 0.052 1250 ae312rah8n7jsz 8.7 5 22 41 68 96 6000 0.097 1100 ae312rah9n5jsz 9.5 5 24 43 73 103 6000 0.099 1100 ae312rah10njsz 10 5 35 45 80 100 6000 0.11 1100 ae312rah11njsz 11 5 35 45 80 100 6000 0.11 1100 ae312rah12njsz 12 5 35 50 85 100 6000 0.13 1050 ae312rah13njsz 13 5 35 50 85 100 6000 0.13 1050 ae312rah15njsz 15 5 40 55 90 105 6000 0.13 1400 ae312rah16njsz 16 5 40 55 90 105 5500 0.16 1000 ae312rah18njsz 18 5 40 55 90 105 5500 0.16 1000 ae312rah20njsz 20 5 40 55 90 105 4900 0.16 1000 ae312rah22njsz 22 5 40 55 90 105 4600 0.17 950 ae312rah24njsz 24 5 40 50 85 95 3800 0.21 950 ae312rah27njsz 27 5 40 50 85 95 3700 0.22 750 ae312rah30njsz 30 5 40 50 85 90 3300 0.23 650 ae312rah33njsz 33 5 40 50 85 90 3200 0.23 650 ae312rah36njsz 36 5 40 50 85 90 2900 0.26 600 ae312rah39njsz 39 5 40 50 85 90 2800 0.26 600 ae312rah43njsz 43 5 40 50 85 75 2700 0.27 600 ae312rah47njsz 47 5 38 50 85 75 2600 0.29 550 ae312rah51njsz 51 5 38 50 85 75 2500 0.33 550 ae312rah56njsz 56 5 38 50 85 75 2400 0.35 530 ae312rah62njsz 62 5 38 50 85 75 2300 0.43 450 ae312rah68njsz 68 5 38 50 85 75 2200 0.38 520 ae312rah72njsz 72 5 34 50 80 60 2100 0.56 470 ae312rah75njsz 75 5 34 50 80 60 2050 0.56 450 ae312rah82njsz 82 5 34 50 80 55 2000 0.60 400 ae312rah91njsz 91 5 34 45 80 55 1900 0.64 400 ae312rahr10jsz 100 5 34 45 75 50 1800 0.68 380 ae312rahr11jsz 110 5 32 45 75 50 1350 1.2 350 ae312rahr12jsz 120 5 32 45 75 50 1600 1.3 310 ae312rahr13jsz 130 5 32 45 75 50 1450 1.4 250 ae312rahr15jsz 150 5 32 45 70 ? 1400 1.5 240 ae312rahr16jsz 160 5 32 45 65 ? 1350 2.1 210 ae312rahr18jsz 180 5 25 45 60 ? 1300 2.2 200 ae312rahr47gsz 470 2 28 ? ? ? 650 6.0 120 1. when ordering, please specify testing code: ae312rahr47gs z testing: z = coilcraft critical products environmental stress conditions testing. h = coilcraft qual + coilcraft hi-rel burn-in p = coilcraft qual + mil-std-981 class s group a screening n = coilcraft qual + mil-std-981 class b group a screening c = coilcraft qual + mil-std-981 class s group a screening + mil-std-981 class s group b qualification w = coilcraft qual + mil-std-981 class b group a screening + mil-std-981 class s group b qualification 2. inductance measured at 100 mhz, 0.1 vrms, 0 adc using a coilcraft smd-a fixture in an agilent/hp 4286a impedance analyzer with coilcraft-provided correlation pieces. 3. q measured at 100 mhz using an agilent/hp4291a with agilent/ hp 16193 test fixture. 4. srf measured using an agilent/hp 8753d network analyzer and a coilcraft smd-d test fixture. 5. dcr measured on a cambridge technology micro-ohmmeter and a coilcraft ccf858 test fixture. 8. electrical specifications at 25c. refer to doc 362 ?soldering surface mount components? before soldering.
|
